Flexibility is a key feature of Bluewave, enabling a wide range of configurations to suit the control requirements of each project. Ease of use is assured by simple integrated push buttons and meaningful LED displays that clearly show the control status.
Each channel can be used to detect occupancy and/or light levels with the ability to connect up to six occupancy sensors to each Bluewave controller. The channels can operate independently of each other, providing a wide range of configurations within one zone or across two zones.
These are just some examples of the configurations
that can be easily achieved with BlueWave:
● Two stages of light level within a single zone
● Occupancy and light levels in a single zone
● Occupancy and light levels across two zones
● Occupancy and timed delay
● Two run-back timers

Click to view the BlueWave data sheet!
● 2 or 3 channel lighting controller
● Occupancy control for 2 or 3 zones
● Independent light level control for 2 or 3 zones
● Suitable for internal and external lighting applications
● Low cost flexible controller
● Qualifies for Carbon Trust Enhanced Capital Allowance scheme
● Manual override of all switching
● Facility for remote switching
● Volt-free change-over contacts for linking to BMS
● Variable time-delays up to 60 minutes or up to 12 hours
● Easy to configure and re-configure on site
● At-a-glance status indication
Operating Environment
| Operating temperature range: |
0°C to 40°C |
| Operating humidity range: |
0 to 90% RH |
| Control IP rating: |
IP30 |
| Pollution degree: |
II environment |
| Control safety construction: |
Class II |
| Mains supply: |
230Vac nominal
200Vac to 265Vac actual
50Hz |
| Recommended control supply fuse: |
3A |
| Rated impulse voltage: |
2500V |
| Dimensions: |
216X 124X 62mm |
| Conformities: |
EMC – 89/336/EEC
LVD – 73/23/EEC |
Performance Specifications
| Maximum sensor rating: |
175mA |
| Timer Range: |
10s -60m or 10s-12 hours (selectable) |
| Light Level Control: |
Min to Max |
| Status Indicators: |
Red LED (Channel off)
Blue LED (Channel on) |
Explanation of flashing LED’s
|
Fashing red (Temporary Override off)
Flashing blue (Temporary Override on)
Flashing red & blue (Permanent override on) |
BW2/C Version Electrical Specifications
The power supply is isolated, therefore all remote sensor and remote switch wiring to the control does not need to be mains level rated, but should be insulated to the highest voltage present where entering the control box.
| Channel 1 relay rating: |
16A/240Vac resistive
6A/240Vac inductive/fluorescent
3A/240Vac compact fluorescent |
| Channel 2 relay rating: |
16A/240Vac resistive
6A/240Vac inductive/fluorescent
3A/240Vac compact fluorescent |
BW3/C Version Electrical Specifications
All as above, plus additional relay (Channel 2).
| Channel 1 relay rating: |
16A/240Vac resistive
6A/240Vac inductive/fluorescent
3A/240Vac compact fluorescent |
| Channel 2 relay rating: |
16A/240Vac resistive
6A/240Vac inductive/fluorescent
3A/240Vac compact fluorescent |
| Channel 2, second relay rating: |
16A/240Vac resistive
6A/240Vac inductive/fluorescent
3A/240Vac compact fluorescent |
Order Codes
| BW2/C |
Blue Wave – Two Channel Controller |
| BW3/C |
Blue Wave – Two Channel Controller
with additional Channel 2 relay output |
| PIR/CM |
Ceiling Sensor |
| BW/MINI |
Blue Wave – Mini Sensor |
| PIR/WH |
Weather Proof Sensor |
| BW/35 |
Blue Wave – Corridor Sensor |
| BW/CUR |
Blue Wave – High Bay / Curtain Sensor |
| BW/MW |
Blue Wave – Microwave Sensor |
| BW/LUX |
Light Level Sensor – for internal use |
| BW/LUX/WP |
Light Level Sensor – Weatherproof |
Specifications may change without prior notice.
Presence or Absence
BlueWave can be configured to operate with presence detection (lights come on automatically when someone enters the space) or demand-based absence detection (lights may be switched on manually and will be turned off automatically when no presence is detected for the set period). The light level control may also be set to prevent lights coming on in bright conditions.
BlueWave occupancy sensors employ new BlueWave infra-red technologies to provide precise movement detection. BlueWave occupancy and light level sensors as well as manual switch wiring is all extra low voltage (SELV) which makes for simple installation.
BlueWave sensors are also available with dual-detection technologies, combining passive infra-red (PIR) and microwave detection.

Click to view the BlueWave technical data sheet.